Item #xxxxxxxxxxxx
xxxxxxxxxxxxx
Model : HD-1895-BZ
HD-1895-WH
USE AND CARE GUIDE
Battery-Operated Motion Sensor Light
Questions, problems, missing parts? Before returning to the store,
call Defiant Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.COM
THANK YOU
We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light.
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products
available for your home improvement needs. Thank you for choosing Defiant!
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
1
28-May-18 9:18:21 AM
Warranty
3-YEAR WARRANTY
Specifications
Detection Range
Sensing angle
Up to 33 ft.
Up to 180°
LED Lumens
1050 lm
Operating temperature
Power requirements
-13°F to +113°F
4 Alkaline “D” cell batteries - 1.5V (not included)
Pre-Installation
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present (see Hardware Included on page 4). If any part is
missing or damaged, do not attempt to assemble, install, or operate this light fixture.
Estimated installation time: 15 - 20 minutes
TOOLS THAT MAY BE REQUIRED
Depending on your particular installation, you may need these tools.
Phillips
screwdriver
Flathead
screwdriver
Drill
Ladder
Drill bits
Safety goggles
Level
3
HOMEDEPOT.COM
Please contact 1-866-308-3976 for further assistance.
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
3
28-May-18 9:18:21 AM
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware shown is not to scale
AA
BB
CC
Part
Description
Quantity
AA
Screws
2
BB
CC
Screw pegs
2
3
Diffuser panels
PACKAGE CONTENTS
C
A
D
B
Part
Description
Quantity
A
Lamp head
Main body
3
B
C
D
1
1
1
Mounting plate
Motion sensor
4
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
4
28-May-18 9:18:21 AM
Installation
Determining the Mounting Location
1
□
Determine the mounting location - wall or eave
mount.
Wall mount
Eave mount
Removing the Mounting Plate
2
NOTE: This fixture comes with a mounting plate (C). It is
pre-assembled on the light fixture (B) for shipping.
B
□
Gently pull the bottom tab (1) of the wall mounting
plate (C) away from the light body (B).
C
1
Installing the Batteries
3
NOTE: Ensure the ribbon inside the battery compartment
is located behind the batteries and the loose end of the
ribbon is accessible to help remove the batteries when
needed.
B
3
□
Install 4 x Alkaline “D” 1.5V batteries (3) (not
included) into the baterry compartment.
Make sure the polarity (+ & -) of the batteries is
correct as shown in the battery compartment.
5
HOMEDEPOT.COM
Please contact 1-866-308-3976 for further assistance.
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
5
28-May-18 9:18:22 AM
Installation (continued)
Installing the Mounting Plate
4
A. Wall Mount
□
Remove the two rubber gaskets (2) from
mounting plate (C).
□
Place the mounting plate (C) against the wall with
the word “UP” facing you (see illustration). Ensure
the mounting plate (C) is level. Mark the hole
locations.
□
If mounting to a wooden surface like a deck, you
can install the mounting screws (AA) through
the mounting plate (C) and into the wood with a
screwdriver, or with a drill and bit driver.
C
2
You can also drill two pilot holes into the wood
mounting surface with a 1/8 inch drill bit and then
install the screws.Reinstall the rubber gaskets (2)
over the screws to keep the unit weatherproof.
□
If mounting to wall board or brick, drill two pilot
holes into the mounting surface, using a 7/32 inch
drill bit.
BB
C
AA
Insert the wall pegs (BB) and attach the mounting
plate (C) using the two mounting screws (AA) and
install the rubber gaskets (2) over the screws to
keep the unit weatherproof.
2
Mounting the Light Fixture
5
□
Attach the light fixture (B) to the mounting
plate (C).
□
Press the unit on the bottom to the mounting
plate. You should hear a “Click” sound. This
indicates that the device is securely attached to
the mounting plate.
C
B
Click!
6
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
6
28-May-18 9:18:22 AM
Installation (continued)
Installing the Mounting Plate
Mounting the Light Fixture
6
7
B. Eave or Ceiling Mount
Place the mounting plate (C) against the ceiling.
Mark the hole locations.
□
□
Attach the light fixture (B) to the mounting
plate (C). Support the back-plate from behind
with one hand and push the light onto the
back-plate with the other hand.
□
If mounting to a wooden surface like a deck, you
can install the mounting screws (AA) through
the mounting plate (C) and into the wood with a
screwdriver, or with a drill and bit driver.
B
C
You can also drill two pilot holes into the wood
mounting surface with a 1/8 inch drill bit and
then install the screws.
□
If mounting to wall board or brick, drill two pilot
holes into the mounting surface, using a 7/32
inch drill bit.
Insert the wall pegs (BB) and attach the mounting
plate (C) using the two mounting screws (AA)
with a very long Phillips screwdriver.
□
Press the unit on the bottom to the mounting
plate (C). You should hear a “Click” sound.
This indicates that the device (B) is securely
attached to the mounting plate.
BB
AA
B
C
C
Click!
Operation
Adjusting the Lamp Heads
1
□
If needed, gently grasp the lamp head (A), it can be
tilted down by 60°and upward by 30°. It also can
be panned out 90° and panned in 40°.
□
Hinge (4) can pan the lights in and out.
Hinge (5) can tilt the lamps up and down.
5
4
A
7
HOMEDEPOT.COM
Please contact 1-866-308-3976 for further assistance.
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
7
28-May-18 9:18:23 AM
Operation (continued)
Adjusting the Sensor Head
2
□
The motion sensor gets a full 180° of coverage, so it senses from wall to wall. However, if the sensor is
mounted on a corner and you would like additional coverage on one side or the other, the sensor (D) can
be rotated left and right.
D
Adjusting the Control Settings
3
Adjusting The Selector Switch
Adjusting The DUSK LEARN
ECO
OFF - Select OFF to completely switch off the
DUSK LEARN
device.
Your motion sensor light is factory preset to only
work after dusk. For most people, this will be the
best setting and you will not need to make any
adjustment.
15 S - This is the normal AUTOMATIC motion sensing
mode. The lights will stay as long as unit detects
motion. After the unit no longer senses motion, it will
turn off after 15 seconds. Any re-triggers will extend
the time for another 15 seconds.
However, if desired, you can set your own “dusk”
level; which will determine how dark it needs to be
before the motion sensor works.
XTEN - The lights will stay on at 100% brightness for
12 seconds and then drop to about 20% for another
48 seconds, if it no longer detects motion. If motion is
detected again, the lights will go back up to 100% for
12 seconds and then drop to about 20% for 48 more
seconds. Any re-trigger will extend the on time for the
same period.
□ Press the DUSK LEARN button once to recalibrate
the dusk level to the current light level. The motion
sensor will now activate at this light level from now
on. If you want the lights to work day and night,
regardless of the light level, push the DUSK LEARN
button while the unit is outdoors during the day, or
hold the unit up to a light and push the dusk learn
button. Now, the motion sensor will turn on the lights
day or night, regardless of the surrounding light level.
The lights will blink once to let you know it has reset
the dusk level.
ECO - This is energy saving mode. The lights will come
on at 70% brightness and stay on as long as motion is
detected. After the unit no longer senses motion, it will
turn off after 15 seconds. Any re-triggers will extend
the time for another 15 seconds. This setting will
extend your battery life by up to 30%.
□ To return the default factory setting, press the
DUSK LEARN button twice within 2 seconds, the
lights will blink twice to indicate that you have
returned to default factory setting.
8
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
8
28-May-18 9:18:23 AM
Operation (continued)
Using the Diffuser Panels
4
If you want to reduce the glare of the lights, attach the diffuser panels to the lamp heads as shown below.
This also prevents the LEDs from being seen during daylight hours. Some people may prefer the
appearance of the light fixture with the diffuser panels in place.
You can remove the diffuser panels by using a small flathead screwdriver. Insert screwdriver into tab and
gently twist to pop the diffuser panels out of the lamp heads.
With Diffuser Panel
A
CC
CC
Without Diffuser Panel
CC
A
Care and Cleaning
□
□
To prolong the original appearance, clean with clear water and soft, damp cloth only.
Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration
of the finish. This is not a defect in the finish and will not be covered by the warranty.
□
Do not spray with a hose or power washer.
9
HOMEDEPOT.COM
Please contact 1-866-308-3976 for further assistance.
IQA HD-LB1895-IM-US-20180507B-FINAL.indd
9
28-May-18 9:18:23 AM
Troubleshooting
Problem
Possible Cause
Solution
The light will not come on.
□
□
Daylight turn-off (photocell) is in effect.
□
□
Set the DUSK LEARN at
desired lux level.
Reposition the unit within
your desired detecting range.
The motion sensor is out of coverage
area.
□
□
Recheck with new batteries.
□
□
Batteries are dead.
Recheck and make sure
batteries are installed
with the correct polarity
(+ & -), as shown in the
battery compartment.
Batteries may be incorrectly installed
The light comes on during
the day.
□
□
The motion sensor may be installed in a
relatively dark location.
□
□
The light fixture is operating
normally under these
circumstances.
DUSK LEARN was set in daylight
conditions.
Reset the DUSK LEARN
setting by pushing once at
the desired level of darkness,
or return to the factory
setting by pushing the DUSK
LEARN button twice within 2
seconds.
The light comes on for no
apparent reason.
□
□
The motion sensor may be sensing
small animals or automobile traffic, or
other heat sources.
□
□
Re-aim the motion sensor.
Strong wind may activate the sensor.
The light fixture is operating
normally under these
circumstances.
The lights stay on
continuously.
□
□
Another regular light is positioned too
close to the motion sensor or pointed
at nearby objects that cause heat to
trigger the motion sensor.
□
□
Reposition the motion sensor
away from the light or nearby
objects.
Same as above.
The motion sensor may be picking up
a heat source like an air vent, dryer
vent, or brightly painted, heat-reflective
surface.
10
IQA HD-LB1895-IM-US-20180507B-FINAL.indd 10
28-May-18 9:18:24 AM
Questions, problems, missing parts? Before returning to the store,
call Defiant Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.COM
Retain this manual for future use.
IQA HD-LB1895-IM-US-20180507B-FINAL.indd 11
28-May-18 9:18:24 AM
|