model t10165
high-precision
mini rotary tool
oWner's manual
Copyright © JUNE, 2009 By grizzly iNdUstrial, iNC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#ts11870 priNtEd iN JapaN
safety
for your own safety read instruction manual
before operating this equipment
the purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. this manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. the
progression of symbols is described below. remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
indicates an imminently hazardous situation which, if
not avoided, Will result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
it may also be used to alert against unsafe practices.
this symbol is used to alert the user to useful infor-
NOTICE
mation about proper operation of the equipment.
safety instructions for machinery
4. alWays
use
hearing
1. read through the entire
manual before starting
protection When operating
machinery. Machinery noise can
cause permanent hearing damage.
machinery. Machinery presents
serious injury hazards to untrained
users.
5. Wear proper apparel. do
Not wear loose clothing, gloves,
neckties, rings, or jewelry which may
get caught in moving parts. Wear pro-
tective hair covering to contain long
hair and wear non-slip footwear.
2. alWays use ansi approved
safety glasses
When
operatingmachinery.Everyday
eyeglasses only have impact resistant
lenses, they are Not safety glasses.
6. never operate machinery
When tired, or under the
influence of drugs or
alcohol. Be mentally alert at all
times when running machinery.
3. alWays
Wear
a
niosh
approved respirator When
operating machinery that
produces dust. Wood dust is
a carcinogen and can cause cancer
and severe respiratory illnesses.
Model t10165 high-precision Mini rotary tool
-1-
safety instructions for machinery
7. only allow trained and properly super-
16. maKe sure guards are in
vised personnel to operate machin-
ery. Make sure operation instructions
are safe and clearly understood.
place and WorK correctly
before using machinery.
17. remove adJusting Keys and
Wrenches. Make a habit of check-
ing for keys and adjusting wrenches
before turning machinery oN.
8. Keep children and visitors
aWay. Keep all children and visitors
a safe distance from the work area.
9. maKe WorKshop child proof.
Use padlocks, master switches, and
remove switch keys.
18. checK for damaged parts
before using machinery.
Check for binding and alignment of
parts, broken parts, part mounting,
loose bolts, and any other conditions
that may affect machine operation.
repair or replace damaged parts.
10. never leave When machine is
running. turn power off and allow
all moving parts to come to a com-
plete stop before leaving machine
unattended.
19. do not force machinery. Work
at the speed for which the machine or
accessory was designed.
11. do not use in dangerous
environments. do Not use
machinery in damp, wet locations,
or where any flammable or noxious
fumes may exist.
20. secure WorKpiece. Use clamps
or a vise to hold the workpiece when
practical. a secured workpiece pro-
tects your hands and frees both
hands to operate the machine.
12. Keep WorK area clean and
Well lit. Clutter and dark shadows
may cause accidents.
21. do not overreach. Keep proper
footing and balance at all times.
13. use a grounded eXtension
cord rated for the machine
amperage. Undersized cords over-
heat and lose power. replace exten-
sion cords if they become damaged.
do Not use extension cords for
220V machinery.
22. many machines Will eJect
the WorKpiece toWard the
operator. Know and avoid con-
ditions that cause the workpiece to
"kickback."
23. Be aware that certain woods may
cause an allergic reaction in peo-
ple and animals, especially when
exposed to fine dust. Make sure you
know what type of wood dust you will
be exposed to and always wear an
approved respirator.
14. alWays disconnect from
poWer
source
before
servicing machinery. Make
sure switch is in oFF position before
reconnecting.
15. maintain machinery With
care. Keep blades sharp and clean
for best and safest performance.
Follow instructions for lubricating and
changing accessories.
-2-
Model t10165 high-precision Mini rotary tool
additional safety instructions for
mini rotary tool
1. clamp the WorKpiece. if the
4. electrocution hazards. do
spinning tool slips from the workpiece
while you are holding it, you could
suffer piercing or abrasion injuries.
do Not hold the workpiece with one
hand and operate the tool with the
other. secure the workpiece in a vise
or work-holding device before starting
the rotary tool.
Not operate this tool in wet or damp
conditions. remove all liquids from
the work area before beginning oper-
ation. Make sure your hands are
clean and dry.
5. WorKpiece contact. Jamming
the spinning tool against the workpiece
could cause the workpiece or tool to
shatter and send debris in all direc-
tions. Firmly grasp the rotary tool and
ease it into the workpiece.
2. eXplosion hazards. sparks
from the grinding operation can eas-
ily ignite flammable gasses, fluids, or
materials. alWays make sure that
these substances are completely
removed from the work area before
beginning operation.
6. tool capacities. to avoid dam-
age to the tool or workpiece that
may cause operator injury, alWays
operate this tool within the capacities
stated on page 4.
3. entanglement
hazards.
loose clothing or jewelry can become
entangled with the spinning tool, pull-
ing hands and fingers into the bit.
to avoid this risk, remove jewelry,
secure loose clothing, button long
sleeves, and tie back long hair.
7. accidental startup. to avoid
unexpected startup that may cause
injuries, alWays make sure the rota-
ry speed dial is turned OFF before
connecting the tool to power.
no list of safety guidelines can be
complete. every shop environment is
different. always consider safety first,
as it applies to your individual work-
ing conditions. use this and other
machinery with caution and respect.
failure to do so could result in seri-
ous personal injury, damage to equip-
ment or poor work results.
Model t10165 high-precision Mini rotary tool
-3-
introduction
foreword
contact info
We are proud to offer the grizzly Model
t10165 high-precision Mini rotary tool.
this model is part of a growing grizzly fami-
ly of fine power tools. When used according
to the guidelines set forth in this manual,
you can expect years of trouble-free, enjoy-
able operation and proof of grizzly’s com-
mitment to customer satisfaction.
if you have any comments regarding this
manual, please contact us:
grizzly industrial, inc.
C/o technical documentation Manager
p.o. Box 2069
Bellingham, Wa 98227-2069
Email: manuals@grizzly.com
it is our pleasure to provide this manual
with the Model t10165. it was written to
encourage safety considerations and guide
you through general operating procedures
and maintenance.
Most importantly, we stand behind our
tools. if you have any service questions or
parts requests, please call or write us at
the location listed below.
grizzly industrial, inc.
1203 lycoming Mall Circle
Muncy, pa 17756
phone: (570) 546-9663
Fax: (800) 438-5901
the specifications, details, and photo-
graphs in this manual represent the Model
t10165 as supplied when the manual was
prepared. however, owing to grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obligation
on the part of grizzly.
E-Mail: techsupport@grizzly.com
Web site: http://www.grizzly.com
machine data
required power..................................110V
power output (at no load) ...................20W
Number of speeds......................... Variable
speed range............... 4,000–14,000 rpM
Max. Continuous operating time......8 min.
Max. tool Bit diameter...................... 7 mm
read the manual before operation.
become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. serious
personal injury may result if safety or
operational information is not under-
stood or followed.
-4-
Model t10165 high-precision Mini rotary tool
setup
unpacking
inventory
model t10165 inventory (figure 1)
a. Collet 3⁄32" (pre-installed)..................... 1
b. Mini rotary tool................................. 1
c. abrasive Cones:
—Coarse grit (yellow)....................... 5
—Medium grit (Blue) ......................... 5
d. threaded Mandrels (for cones).......... 2
e. Collet 1⁄8"............................................. 1
f. steel Bits:
your new mini rotary tool was carefully
packaged for safe shipping. if you dis-
cover any damage after you have signed
for delivery, immediately call Customer
Service at (570) 546-9663 for advice.
save the containers and all packing materi-
als for possible inspection by the carrier or
its agent. Otherwise, filing a freight claim
can be difficult.
—round head 1.4mm ....................... 1
—Cylindrical 2.1mm........................... 1
g. diamond Bits:
When you are completely satisfied with
the condition of the shipment, you should
inventory the contents.
—round head 2mm .......................... 1
—Flame 3mm .................................... 1
—Cylindrical 1.2mm........................... 1
—spear 2mm..................................... 1
a
B
C
g
E
d
F
figure 1. Model t10165 inventory.
Model t10165 high-precision Mini rotary tool
-5-
operations
3. Fully insert the mandrel or bit shank
into the collet until it stops, then re-
tighten the collet nut.
note: Only tighten the collet nut until
the mandrel or bit cannot be removed
when you tug on it. Overtightening may
damage the components.
operating this tool can propel objects
into the air that may cause eye damage.
to protect yourself from this hazard,
alWays wear ansi approved safety
glasses or goggles during operation.
operation rules
follow these rules to ensure a safe and
efficient operation:
mandrels & bits
•
•
turn the rotary speed dial to OFF
before connecting the tool to power.
your mini rotary tool is supplied with two
threaded mandrels that hold that hold the
abrasive cones. to install an abrasive
cone onto a mandrel, screw the threaded
tip of the mandrel into the bottom of the
cone.
to prevent injuries from tool slippage,
alWays secure the workpiece in a
vise or other clamping device. NEVEr
hold the workpiece by hand during
operation.
note: The cones with yellow bottoms are
coarse abrasives, and the ones with blue
bottoms are a medium abrasive.
•
•
•
For efficient control of the tool, start
your operation with the slowest speed,
then increase the speed as needed.
to install a mandrel or bit:
to avoid the tool slipping in your hand,
make sure your hands are clean and
dry.
1. disCoNNECt tool FroM poWEr!
2. press and hold the spindle lock to keep
the spindle from rotating, then loosen
the collet nut (see figure 2).
to prevent excessive wear of the motor
components, NEVEr operate this tool
for longer than five continuous minutes.
turn it OFF after this time and allow it
to cool for five minutes.
Collet Nut
rotary speed dial
•
•
to ensure a good finish, ease the cone
or bit into the workpiece. Jamming it
into the workpiece may damage the
tool components or the workpiece.
spindle lock
When using the abrasive cones, use
the tip of the cone. otherwise, the abra-
sive material may unravel.
figure 2. Model t10165 controls.
-6-
Model t10165 high-precision Mini rotary tool
accessories
t20501—face shield
h1432—multi-positional hobby vise
crown protector 4"
t20502—face shield
crown protector 7"
this handy, go-anywhere vise features a
powerful suction mechanism that securely
attaches the vise to any smooth, flat sur-
face. the swivel head can be positioned
in just about any configuration and locks
in place with a high torque lock ring. ideal
for hobby use around the home or take it
anywhere. steel jaws have protective rub-
ber pads and measure 23⁄4" wide. open
capacity is 21⁄2".
t20503—face shield Window
t20452—"Kirova" anti-reflective
safety glasses
t20451—"Kirova" clear safety glasses
h0736—shop fox® safety glasses
h7194—bifocal safety glasses 1.5
h7195—bifocal safety glasses 2.0
h7196—bifocal safety glasses 2.5
t20452
t20451
t20502
t20503
h7194
h0736
figure 3. Eye protection assortment.
figure 4. Model h1432 hobby vise.
Model t10165 high-precision Mini rotary tool
-7-
replacement parts
1
Consists of:
5 Each Coarse Abrasive Cones
5 Each Medium Abrasive Cones
2
Consists of:
1 Each Round Head 1.4mm Steel Bit
1 Each Cylindrical 2.1mm Steel Bit
1 Each Round Head 2mm Diamond Bit
1 Each Flame 3mm Diamond Bit
1 Each Cylindrical 1.2mm Diamond Bit
1 Each Spear 2mm Diamond Bit
3
Consists of:
1 Each Collet Nut
1 Each 3⁄32" Collet
1 Each 1⁄8" Collet
2 Each Threaded Mandrels
REF PART #
DESCRIPTION
ABRASIVE KIT
BIT KIT
REF PART #
PT10165003
DESCRIPTION
COLLET/MANDREL KIT
1
2
PT10165001
PT10165002
3
-8-
Model t10165 high-precision Mini rotary tool
Warranty
grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. this warranty does not apply to defects due directly or
indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-
nance. this is grizzly’s sole written warranty and any and all warranties that may be implied
by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant or represent that the merchandise
complies with the provisions of any law or acts unless the manufacturer so warrants. in no
event shall grizzly’s liability under this warranty exceed the purchase price paid for the prod-
uct and any legal actions brought against grizzly shall be tried in the state of Washington,
County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
to take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “return authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. proof of purchase must accompany the merchandise.
the manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to use
this warranty.
please feel free to write or call us if you have any questions about the machine or the
manual.
grizzly industrial, inc.
1203 lycoming mall circle
muncy, pa 17756
phone: (570) 546-9663
fax: (800) 438-5901
e-mail:
techsupport@grizzly.com
Web site: http://www.grizzly.com
thank you again for your business and continued support. We hope to serve you again
soon!
Model t10165 high-precision Mini rotary tool
-9-
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
|
GPX Refrigerator 1409 0319 10 User Manual
Graco Inc Paint Sprayer 222300 User Manual
Hamilton Beach Can Opener Smooth Edge User Manual
Hamilton Beach Food Processor 72850 User Manual
Hans Grohe Indoor Furnishings 31100001 User Manual
Harbor Freight Tools Router 97385 User Manual
Harbor Freight Tools Water Pump 92274 User Manual
Harman Stove Company Range SF 150 SF 250 User Manual
HTC Cell Phone ROSE130 User Manual
Husqvarna Lawn Mower 216 User Manual